Your Ellara One, from box to first session.
A short guide to setup, the controller, the six programs and care. The full manual is one tap away.
In the box.
- The Ellara One mask360 LEDs, medical-grade silicone
- ControllerWired, full-color display
- Adjustable head strap
- USB-C charging cable
- User manual
- Premium carrying pouch
Check everything when you unbox. If anything is missing or damaged, email us straight away.
Try the Program and Brightness buttons.
Three buttons. That's all.
The controller is wired to the mask and sits in a pocket or on your lap during a session.
- PowerHold 2 to 3 sec
- Hold to turn the mask on or off. The screen confirms the power status.
- ProgramPress
- Each press steps to the next program, M1 to M6, then back to M1. The active program shows on the display.
- BrightnessPress
- Steps through 50%, 75% and 100%. Start at 50% and build up as your skin gets used to it.
- DisplayRead only
- Shows the countdown timer, program name, active wavelengths, brightness level and battery.
Six programs. One button.
Press PROGRAM to step through M1 to M6. Every program runs for 10 minutes and shuts off on its own.
Wavelengths in nanometers: 415 blue, 590 yellow, 630 red, 850 and 1072 near-infrared (invisible to the eye). Programs are preset and can't be customized. Brightness: 50%, 75% or 100%.
How to use it.
Set it up once, then it's ten minutes, three to four times a week.
Once, before your first session
-
Set up the mask
Peel the protective film off the LED surface. Thread the head strap through the buckle slots on both sides, then plug the controller cable into the mask's power port.
-
Charge it fully
About 3 hours over USB-C with the included cable, before your first session.
-
Do a patch test
Hold the mask against your forearm for a full 10-minute session at 50% brightness, then wait 24 hours. If there's no redness, itching or irritation, you're ready for your face.
Every session
-
Start with clean, dry skin
Remove makeup, SPF and skincare first. Residue can block light and reduce results.
-
Put the mask on
Line up the eye, nose and mouth openings, then tighten the strap until the mask sits flush against your skin.
-
Power on, pick a program
Hold POWER for 3 seconds. Press PROGRAM to choose M1 to M6, then BRIGHTNESS for 50%, 75% or 100%. New to light therapy? Start at 50% and build up over the first one to two weeks.
-
Relax for 10 minutes
The timer runs itself and the mask switches off when it's done. Keep your eyes closed if the light feels bright, and don't stare into the LEDs. A gentle warmth is normal.
-
Follow with your serum
Skin absorbs best right after a session. Apply your serum, then moisturizer, and SPF if it's morning.
Consistency matters more than any single session.
Care and charging.
- 4000 mAh
- Battery
- ~3 h
- Full USB-C charge
Charging
- Charge fully before your first session.
- Use the included USB-C cable and a standard 5V/2A adapter.
- Don't leave it plugged in overnight once it's full.
- If you won't use it for a long while, store it at about 50% charge.
- Avoid charging in very hot or very cold rooms.
Cleaning
- Wipe the inner surface with a soft, slightly damp cloth after each use.
- Or use a gentle, alcohol-free cleanser or micellar water on a cotton pad.
- Let it air dry fully before you put it away.
- Never submerge it or use abrasive materials.
- Keep cleaning products off the LED panels.
Storage and habits
- Keep it in the carrying pouch, away from direct sunlight and extreme heat or cold (15 to 30 °C, 59 to 86 °F).
- Fold it along its natural seam only.
- Look over the mask and cable for damage before each use.
- Don't share it without cleaning it first.
- Keep it out of reach of children.
Safety, before you begin.
The Ellara One is designed for safe home use when used as directed. If you're unsure about any of this, ask your dermatologist or doctor first.
Medical conditions
Don't use it if you have epilepsy, a photosensitivity disorder or lupus. If you're having cancer treatment, ask your doctor first.
Medication
Some medications make skin more sensitive to light, including certain antibiotics, retinoids and NSAIDs. Don't use the mask until you've checked with your prescriber.
Pregnancy
Safety during pregnancy hasn't been established. Ask your doctor before using it while pregnant or breastfeeding.
Skin
Don't use it over open wounds, active infections or severely inflamed skin, or on areas treated with injectable fillers without medical advice.
Skincare on the same day
Skip the mask on days you use products with photosensitizing ingredients, such as certain AHAs, BHAs, retinoids or vitamin C derivatives.
Eyes
Never stare into the LEDs. Make sure the built-in eye shield sits properly before every session.
Age
For adults 18 and over. Keep it out of children's reach. It's a therapeutic device, not a toy.
Water and damage
Not waterproof. Don't use it if the mask, controller, cable or LED surface is visibly damaged, and don't open or modify it. Email us for a replacement.
Stop if
You feel burning or get a persistent rash or swelling. Stop using the mask and seek medical advice. Mild redness after a session is normal and fades within one to two hours.
Specifications
Light
- LEDs
- 360
- Wavelengths
- 415 · 590 · 630 · 850 · 1072 nm
- Irradiance
- 50 mW/cm²
- Per session
- 30 J/cm²
- Programs
- 6 preset (M1 to M6)
- Session
- 10 min, auto shut-off
- Brightness
- 50% · 75% · 100%
Device
- Material
- Medical-grade flexible silicone
- Design
- 3D contoured, eye shield, adjustable strap
- Controller
- Handheld, wired, full-color display
- Battery
- 4000 mAh
- Charging
- USB-C, about 3 hours
- Input
- 5V / 2A, 6 W
- Dimensions
- 345 × 225 × 181 mm
- Clearance
- FDA Cleared, Class II
Want it all in one file?
The full manual has every detail. Questions? Write to us at hello@ellaratherapy.com